View Cart / Checkout
0 items in your cart
Your total is $0.00
Home Products Email us for Catalog or Inquiries Order Form Terms & Conditions Shipping Rates

Search our site:



Vehicular Radios

<< Prev      Currently viewing page 1 of 1      Next >>
Page: 1


   
 
click to view full size image R-105M   -   The Russian Tube Type Radio R-105M was intended for use by infantry units. Operating in one continuous band on 36-46.1mc, with an intended channel spacing of 25 or 50kc. RF power output is rated at 1 watt, FM. Power is derived from two internal Nicad batteries. Durable bakelite housing. Removeable front and back covers. With accessories. 12.3x5.5x11.7, 23 lbs Used, Only two available.
$295.00 each
   
 
Wireless-Set-19   -   Wireless Set 19 MKII WW2 Transceiver. Used not checked,
$275.00 each


   
 
click to view full size image BC-1335   -   BC-1335 (SCR-619)/ No mount Late WW2 Transceiver. (K1H) Used not checked,
$399.00 each




   
 
BC-683   -   BC-683 / SCR-608 superheterodyne FM receiver covers 20 to 27.9MHz. The receiver can deliver an output of approximately 2 watts to its self contained speaker or about 200 milliwatts to its headset circuits. The front panel contains 10 push buttons by means of which any one of 10 preadjusted receiving channels may be selected. IF (nominal) 2.65MHZ. Bandwidth 80KHz. Less dynamotor, modified for AC power supply which is not available. 6.8x12.5x11.5, 40 lbs sh. Used not tested, $150.00 each
$175.00 each


   
 
click to view full size image 508-SYS   -   One BC-603 / SCR-508 superheterodyne FM receiver covers 20 to 27.9MHz. The receiver can deliver an output of approximately 2 watts to its self contained speaker or about 200 milliwatts to its headset circuits. The front panel contains 10 push buttons by means of which any one of 10 preadjusted receiving channels may be selected. IF (nominal) 2.65MHZ. Bandwidth 80KHz. Comes with 24VDC dynamotor. DM-36 (24VDC) is reconditioned. 6.8x12.5x11.5, 40 lbs sh. ------------------------------- One BC-604 FM Transmitter covers 20-28MHz, and delivers a carrier power to the antenna of approximately 30 watts. 10 crystal channels. 8 tubes. DYNAMOTOR NOT AVAILABLE. When they came in there were no dyanmotors in the transmitters and we do not have any. 10.3x18x11.5, 73 lbs sh. Used not tested. Not sold separately. ------------------------------- FT-237 Mount will hold one BC-604 and up to two BC-603 receivers. 54 lbs sh. Used. Not sold separately. ------------------------------- One each of BC-603, BC-604, and FT-237,
$980.00 each


   
 
click to view full size image R-442   -   RECEIVER 30 - 75.95MHZ FM RECEIVER. 920 50 KHZ CHANNELS. Has noise and tone operated squelch. Normally used with antenna system AB-15, MS 116, 117, 118. Power connections through MT-1898 mount and DC power cable, CX-4720 which are included. 13.5, x 5.8 x 8.9, 31 lb sh. Used Reparable,
$345.00 each


Module Covers - for RT524/RT246/R442 radios. Unused.



   
 
click to view full size image CRV-3400   -   A3400 Module Cover for RT524 / RT246 / R442, (F3H)
$3.00 each
   
 
click to view full size image CRV-3500   -   A3500, Module Cover for RT524 / RT246 / R442, (F3H)
$3.00 each
   
 
click to view full size image CRV-3600A   -   A3600A, Module Cover for RT524 / RT246 / R442, (F3H)
$3.00 each
   
 
click to view full size image CRV-4200   -   A4200, Module Cover for RT524 / RT246 / R442, (F3H)
$4.00 each
   
 
click to view full size image CRV-4300   -   A4300, Module Cover for RT524 / RT246 / R442, (F3H)
$3.00 each
   
 
click to view full size image CRV-5100   -   A5100, Module Cover for RT524 / RT246 / R442, (F3H)
$3.00 each
   
 
click to view full size image CRV-8300   -   A8300, Module Cover for RT524 / RT246 / R442, (F3H)
$3.00 each
   
 
CRV-524   -   One each of the following module covers: CRV-3400, CRV-3500, CRV-3600A, CRV-4200, CRV-4300, CRV-5100, CRV-8300. (F3H)
$15.00 each
   
 
click to view full size image CRV-7000   -   A7000 Module Cover for RT246 only, (F3H)
$2.00 each
   
 
click to view full size image CRV-7200   -   A7200 Module Cover for RT246 only, (F3H)
$2.00 each


   
 
click to view full size image CX-4721-10   -   CX-4721 10 ft DC power cable connects MT-1029 to MT-1898 mount. Sh wt 3 pounds. (S2H) Unused
$23.00 each
   
 
click to view full size image MT-1029-U   -   VRC VEHICULAR MOUNT for RT-246 or RT-524/VRC-12 transceivers which are still the standard field radios of the U.S. Army. 5x12.5x16, 25 lbs. (L2X) Used,
$40.00 each
   
 
click to view full size image C-10456   -   VRC Control Box - functions the same as the C-2298/VRC except that it allows remote keying of the intercom or radio RT-524 through a remote keying jack, normally connected to special keying cables in the M1. 3.5x6x4.5, 5 lbs sh. With shorting plug. Used,
$54.50 each
   
 
click to view full size image J-3513A/U   -   VINSON Voice Encryption, When the KY-57 is used in a VRC-12 Series installation special Junction Boxes are inserted between the Base mounting and the Tray of the MT-1029 or MT-1898. These junction boxes contain a number of relays and a low power audio amplifier. They are designed to meet TEMPEST requirements. (C9R) Unused.
$50.00 each
   
 
click to view full size image C-2742   -   Remote Control Box works with the RT-246 for remote selection of the preset frequency channels. 3.3x6x4, 4 lbs sh. Used, One of the mounting tabs is broken off!
$35.00 each
   
 
click to view full size image MX-2096   -   Suppressor Electrical Transient MK-2096/GRC for the VRC-12 Radio Set. This circuit protector consists of a MX-10237 4 pin GRC male connector with a threaded center, indicator light, 2 hole mount bracket, heatsink, and plate which is marked "Danger High Temp 215 degree F". FSN #5915-01-024-3877. It connects directly to either the transceiver or AUX receiver mount. In some applications it replaces the MX-7778 suppressor. No further data. 3 lbs sh. (O2K) Unused,
$20.00 each


   
 
click to view full size image R-108   -   RECEIVER 20 to 28 MHZ FM continuoisly tuneable, variable squelch and audio output impedance 600 ohms. 4.3 MHz. I.F. with tubes 3/1U4, 2/1L4,1A3, 2/3A4, 1S5,2/3Q4,2/6AK5 & 0B2. Voltages req. 135 VDC @ 70 MA. and 6.3 VDC 2 amps. Size: 9x13x7 1/2; wt: 32 lbs. (A2M) Gov't Reconditioned,
$75.00 each
   
 
R-109   -   RECEIVER , same as R-108 except 27-39 MHz. (L2W) Used,
$69.50 each
   
 
PP-282   -   PP-282/GRC Internal Power Supply (24 Volt). Input 25.2 volts (20 to 32 volts), 1.23 amperes max. Output 136 volts dc (105 to 185 volts), 0.118 amperes (J1V) Used, Vibrators bad. No vibrators available seperate. 5.7x2.9x4.1, 7 lbs sh.
$50.00 each


   
 
click to view full size image RT-68   -   TRANSCEIVER, 38-54.9 MHz FM used in vehicles from 1950's until Vietnam era, FM continuously tunable or 100 KHz-step channels. Receives and transmits both voice and 1600 Hz ringing FM; range 10-15 miles. Receiver circuit has variable 1st IF 4.45-5.45 MHz and fixed 1.4 MHz 2nd IF; also squelch and 600 ohm audio output. Transmitter uses crystal-controlled oscillator and oscillator power amp; power output 2 watts (LO) or 15 W (HI). Also meter to monitor xmiter filaments and 90 V input. Requires PP-109 or PP-112 power supply. Tubes 4/1U4, 2E24, 2/1A3, 2/1L4, 4/1R5, 2/1AE4, 1S5, 4/3Q4, 3A4, 3/3A5, 2/3B4, 6AK5. 9x13x11.3, 42 lbs. (Q2V) Used, not tested.
$150.00 each
   
 
RT-66   -   TRANSCEIVER, 20-28MHz FM used in vehicles from 1950's until Vietnam era, Used, not tested.
$115.00 each
   
 
click to view full size image PP-112   -   24 VDC POWER SUPPLY. Vibrator power supply for VRC-10, RT-66-67-68, and other transceivers, provides all voltages from 24 VDC 6.5 amp input. 7.3x9x13, 39 lbs sh. Used, chips in front lip.
$37.00 each
   
 
CX-1211   -   dogbone interconnect cable RT-66,RT-67,RT-68 to PP-109,PP-112 units, (C6P)
$17.00 each
   
 
MM-VRC-8-9-10   -   Maintenance Manual for AN/VRC-8, VRC-9, VRC-10, RT-66, RT-67, RT-68, PP-109, PP-112, PP-281, PP-282, MT-299 repro.
$18.00 each
   
 
click to view full size image C-434-U   -   Local Control for GRA-6 system, Allows remote control of radio by field phone and wire. (Q2W) Used,
$52.00 each
   
 
C-435   -   Control box, Used to duplex two GRC-3-8 LOCAL CONTROL p/o GRA-6, Used,
$26.00 each


   
 
click to view full size image RT-695-CH   -   PRC-41 UHF MANPACK UHF TRANSCEIVER, 225 to 400 MHz AM in 100 KHz steps counter; output at least 3 watts over range. Also has guard channel, Volume, Squelch, and U-77 connection for H-33 handset. Solid-state except for tubes 6442, 4/7077, and 4/7544. Requires 24 VDC 3 amps; 14x11.3x4.5, 22 lbs. sh. Used Checked,
$400.00 each
   
 
MM-PRC-41   -   Maintenance Manual for PRC-41, partial repro,
$27.00 each
   
 
click to view full size image H-33   -   Handset, Has cord with U-77 plug, used-checked, 3 Lbs
$45.00 each
   
 
PP-3700   -   AC POWER SUPPLY, provides 26 VDC for RT-695/PRC-41 from 115/230 VAC 50-400 Hz input. Clips onto and directly connects to RT. CX-8686 cable (not available) connects PP to MT-2976 racl. CX-8687 (not available) connects PP-3700 to AC source. 7.8x11x4.1, 20 lbs sh. Used, tested
$99.50 each
   
 
click to view full size image CY3700-PRC-47   -   LARGE ALUMINUM TRANSIT CASE with rounded corners, hasp fasteners and carrying handles; 21Hx29Wx24D including 6"H top. Spot welded compartments plus two nesting trays; 66 lbs. sh. (D3O) Used,
$65.00 each
   
 
click to view full size image MT-2977   -   VEHICLE MOUNT for PP-3700, 4lbs sh.,
$13.00 each
   
 
click to view full size image AM-6669   -   UHF Power Amp RF Power Amplifier, designed for use with PRC-41 transceiver, but usable with other 225-400MHz xmitters such as PRC-66, ARC-45, etc. Power output: 10 watts from 2-3 W input; "N" connections Solid-state; 24 VDC required. 5.3x6x9.8, 10 lbs sh. Used Reparable,
$225.00 each


   
 
AS-1321   -   PRC-47 Long Wire Antenna 45 foot vinyl-covered with insulators at 15" and 25"; clips at insulators adjust length. Designed for use with 150W HF transceiver; 4 lbs sh. (S2X) Used,
$29.00 each
   
 
CX-8396   -   "Y" CABLE for H-233 to PRC-47 and other RT Units,
$19.50 each
   
 
CX-8393   -   50 ft AC Cable for PRC-47,
$45.00 each
   
 
CX-8395   -   Battery Cable for PRC-47, Connects BB-451 battery with MX-4430 battery adapter to the PRC-47.
$29.00 each
MODULES from RT-671/PRC-47 transceiver. Used not tesed:



   
 
AM-3506   -   AUDIO AMP has mic, sidetone, vox and compressor circuits of TX; AGC & audio for Rx. Requires 20 & 24 VDC. 4.3x4.3x2.8, 2 lbs. (M2L)
$20.00 each
   
 
AM-3507-CON   -   Connector set for AM-3507,
$7.00 each
   
 
C-4311   -   CONTROL OSCILLATOR, 3 lbs. PRC-47
$35.00 each
   
 
O-1032   -   RF OSCILLATOR contains 3 MHz crystal in oven; produces 500 and 100 KHz outputs. Requires 20 VDC; 4.3x4.5x1.3, 1 lb sh. PRC-47
$27.00 each
   
 
PP-3518   -   POWER SUPPLY is the internal power supply for the PRC-47 transceiver. Power input is 115 v 400 HERTZ . The transformer is also used as part of the DC to DC inverter to power the PRC-47 from 28 VDC. The components of the inverter are on the radio chassis, NOT on the power supply chassis and are NOT part of the PP3518. The PP3518 produces -110 vdc PA bias, -32 vdc driver bias, 1500 vdc, 650 vdc, + 300 vdc, +20 vdc, and 6.3 vac for the various circuits of the PRC-47. (Q1Y) 16 lbs sh.,
$35.00 each
   
 
SCH-PP-3518   -   Schematic for PP-3518,
$6.00 each


   
 
click to view full size image 2Z5822-403   -   Small bar knob for R-392 and various GRC radios . Top screw mount. o/a .75"L x .75"W x .5"H. Unused,
$7.00 each
<< Prev      Currently viewing page 1 of 1      Next >>
Page: 1



Home Products Email us for Catalog or Inquiries Order Form Terms & Conditions Shipping Rates


Any problems with the website? Email webmaster@fairradio.com