View Cart / Checkout
0 items in your cart
Your total is $0.00
Home Products Email us for Catalog or Inquiries Order Form Terms & Conditions Shipping Rates

Search our site:



HF Radios

<< Prev      Currently viewing page 1 of 1      Next >>
Page: 1




   
 
click to view full size image R-390A   -   Famous Collins designed military receiver covers 0.5 to 32 MHz AM-CW-MCW in 31 one MHz bands read directly on mechanical counter. Has four Collins mechanical filters and one crystal filter allowing .1-1-2-4-8-16 KHz selectable bandwidths. 100 kHz crystal calibrator, BFO, AGC, noise limiter, dial lock. 600 ohm audio output. 24 tubes, two diodes; two antenna connectors, twinax (balanced) and "C" (unbalanced). Requires 115/230 VAC 60 Hz. 10.5x19x16.8, 92 lbs shipping. Units are disassembled, cleaned, repainted where necessary, reassembled with any unapproved mods removed and any defective parts replaced, tuned to military spec. Sorry no top or bottom covers. Call for availability. (M1E) Used checked.
$1,200.00 each


   
 
click to view full size image HAMMARLUND-SP-600-8021   -   Early production Hammarlund SP-600 JX-6 general coverage MF-HF-VHF(low) receiver serial# 8021. Panel nameplate lists it as R274B/FRR serial# 1035 order no. NObsr-52039. Covers 540 kHz - 54 Mhz modes AM, CW, SSB (via BFO); bandwidths selectable .2-.5-1.3-3-8-13 kHz. Has the Frequency Control Unit which allows crystal controlled reception of up to 6 frequencies. Power requirement 90-270 VAC 50-60 Hz, requires 600 ohm speaker/headphones. In good mechanical and electrical condition, no mods, has factory installed SO-239 antenna connector, some original switches and pots have been replaced. Rack mount front panel is in good condition but may need refinished, all original knobs. Dimensions 19" x 10 1/2" x 18", shipping wt. 75 lb. Used checked.
$650.00 each


   
 
click to view full size image KENWOOD-TS-830S-1020419   -   Kenwood TS-830S amateur transceiver serial #1020419. Transceives on all HF amateur frequencies 160-10M (exc. 60M), modes USB, LSB, CW. Rated 220W PEP input SSB, 180W DC input CW. This is a "hybrid" solid state/tube unit, with 3 tubes, 12BY7A driver and (2) 6146B finals. Has variable bandwidth tuning (VBT), IF shift, variable tone control, variable speech processor, variable noise blanker, RIT/XIT control, and notch filter. Standard 2.4 khz crystal filter, no optional filters installed. Power requirement 120VAC (220VAC/240VAC modifiable), 50/60 Hz. Front panel in very good condition with a few nicks and wear spots on edges, case in good condition with some minor scratches and chips out of finish. Finals have been replaced with military grade Phillips/ECG units. Used checked.
$550.00 each


   
 
click to view full size image KENWOOD-TS-530S-2010458   -   Kenwood TS-530S amateur HF transceiver serial #2010458, transceives on all HF amateur frequencies 160-10M (exc. 60M), modes USB, LSB, CW. Rated 220W PEP input SSB, 180W DC input CW. This is a "hybrid" solid state/tube unit, with 3 tubes, 12BY7A driver and (2) 6146B finals. Has IF shift, variable noise blanker, and RIT/XIT control. Standard 2.4 khz crystal filter, no optional filters installed. Power requirement 120/220/240 VAC 50/60 Hz. Front panel is in very good condition with some minor wear on right upper corner; case is intact, no dents, has been primered in preparation for repainting, a few small rust spots showing through the paint on the left side. Finals appear recently replaced, show very good on tube tester. A very good "starter" or second rig. Used checked,
$400.00 each


   
 
click to view full size image KENWOOD-FM-430   -   Kenwood FM-430 FM unit for the TS-430S transceiver. With cables, cable ties, screws, and installation sheet repro. (E1H) Used checked.
$65.00 each


   
 
click to view full size image R-1051B-ZZ4   -   R-1051B Radio receiver, 2-30 MHz, 2-4 microvolt sensitivity, direct digital frequency synthesis, 0.1 KHz increments, USB/LSB/ISB/AM/FSK, bandwidths: 3.1/6KHz (tied to mode), solid-state except for two rf tubes, 7"h X 17.4"w X 18.9"d, 90 lbs sh, 115 VAC 48-450 Hz 55 W. (C2P) Used checked,
$695.00 each
   
 
MM-R-1051   -   R-1051B Maintenance Manual Navy shipboard HF receiver repro
$58.00 each


   
 
click to view full size image RF-301-ZZ1   -   Harris GRC-165/RF-301 hybrid solid-state/tube finals transceiver covering 2 to 15 MHz USB-LSB-AM-CW in 1 KHz steps. Output 100 watts PEP SSB, 25 W AM nominal into 52 ohms. Has modified oscillator board. Requires carbon or high impedance dynamic microphone (not incl., no mic connector available). With 120VAC power cord. Used reparable,
$395.00 each
   
 
MM-GRC-165   -   Maintenance Manual AN/GRC-165 Mil version Harris RF-301. repro
$40.00 each
   
 
click to view full size image RF-302R-HD-GRN   -   RF Communications (Harris) RF-302R remote antenna coupler control head only, companion to the AN/GRC-165 (RF-301) transceiver. Case in good condition, green color, "B" meter has some discoloration, not checked. We do not have the remote coupler. Used,
$80.00 each


   
 
click to view full size image YAESU-FRG-8800-040648   -   Yaesu FRG-8800 general coverage HF communications receiver ser# 040608 covers 150 kHz - 29.999 Mhz, modes AM (wide/narrow), USB, LSB, CW (wide/narrow), FM narrow. Utilizes the microprocessor controlled "CAT" system, which allows remote control of all functions via an FIF-series CAT controller (not included) and your PC. Has separate connections for 600 ohm balanced/longwire and 50 ohm unbalanced antennas, 12 memory channels, selectable AGC, selectable noise blanker, continuously variable attenuator, direct frequency entry keypad, clock/timer, squelch, tone control, built in speaker. Power requirement 100/120/220/240 VAC 50/60 Hz, 4.5 VDC (AA battery x3) for memory backup. In very good condition, with no scratches on case, one crack in right corner of front panel. Used checked,
$385.00 each
   
 
click to view full size image YAESU-FRG-7700-020692   -   Yaesu FRG-7700 general coverage HF receiver ser# 020692 covers 150 kHz - 29.999 Mhz in 30 bands, modes AM (wide/medium/narrow), USB, LSB/CW, FM. Has separate connections for 600 ohm balanced/longwire and 50 ohm unbalanced antennas, 12 memory channels, selectable AGC, noise blanker, continuously variable attenuator, clock/timer, squelch, tone control, built in speaker. Power requirement 100/120/220/240 VAC 50/60 Hz, 4.5 VDC (AA battery x3) for memory backup. Unit has a fault in the digital display circuitry, one segment of all digits is continuously lit, there is a separate analog frequency dial below it, all other functions checked as working. Case and front panel in good condition, with no scratches on case, minor wear on upper edge of front panel. Used repairable,
$249.00 each


   
 
click to view full size image HALLICRAFTERS-S85-199904   -   Hallicrafters S85 mark 1A ser# 199904 HF general coverage receiver. Covers 538 kHz to 34 MHz in four bands, AM/CW/SSB (by BFO), with a bandspread dial calibrated for the 80, 40, 20, 15, and 11-10 meter amateur bands, which can also be used as a fine tuning dial. In fair physical condition, scratches and unknown spots on front panel, case has many scratches and bare spots, three knobs not original. Receives on all bands but sensitivity varies widely depending on main tuning dial location, had severe hum on arrival, power supply has been repaired. Unit appears to have been used as a parts resource to physically restore another unit. Requires 105-125 VAC 50-60 Hz. Used repairable w/manual repro.
$125.00 each


   
 
BC-348   -   BC-348 WW2 Receiver less dynamotor. Used not checked,
$295.00 each
   
 
BC-348-DL   -   Dial Lamp for BC-348. (G1V)
2 / $5.00
   
 
click to view full size image R-392-FRPNL-UN   -   R-392 Front Panel (L2P). Sh Wt 5lbs Unused.
$125.00 each
   
 
click to view full size image 25A1   -   24VDC 11 amp output switching power supply which DOES WORK with the R-392 and GRC-106 Receiver / Exciter. Requires 115V or 230V 60Hz. Made by Acme Electric Corporation. 9.5x5x2.5, 6 lbs sh. (L1Y, H6E) Used,
$63.95 each
   
 
click to view full size image CONN-R-392   -   9 PIN Female R-392 Power Connector for R-392, (D1W) Unused,
$40.00 each
   
 
MM-R-392   -   R-392 Maintenance Manual Repro,
$29.00 each
   
 
MM-R-392-FIELD   -   R-392 repro of TM 11-5820-334-35 Field and Depot Maintenance Manual. Dated 21 August 1961.
$31.00 each
   
 
click to view full size image 2Z5822-402   -   Medium bar knob for R-392 and various GRC radios . Top screw mount. o/a 1.125"L x .875"W x .5"H. Unused,
$7.00 each
   
 
click to view full size image 2Z5822-403   -   Small bar knob for R-392 and various GRC radios . Top screw mount. o/a .75"L x .75"W x .5"H. Unused,
$7.00 each
   
 
click to view full size image TCO-1C-200U   -   200KHz Crystal Oven with octal base from R-392. This is the oven only, no crystal.
$20.00 each
R-392 Crystals - Click Here



   
 
TF1A13YY   -   Audio Transformer from R390A Receiver. 10,000 ohm primary, 600 ohm secondary, Frequency response plus or minus 1.5 dB, 200-3500 CPS, 1 Watt Max. (L2E) Used.
$30.00 each
   
 
click to view full size image FL-601   -   800 HZ Audio filter for R-390A receiver. (P1U,I8G) Unused.
$20.00 each
   
 
click to view full size image RF-R390A   -   R-390A RF Amplifier Deck, Includes front gear assembly, set of RF transformers with slugs and slug racks. LESS tubes, crystal oven and counter. 9x12x16, 18 lbs sh. Used,
$125.00 each
   
 
click to view full size image RCBS1901017BK1   -   Standard 19" Rack Cabinet for R-390A, R-388, SP-600, etc... 16-gauge steel, Rails are fixed both front and rear, round hole punched for 10-32 clip-nuts to full EIA hole centers (5/8 - 5/8 - 1/2 inch spacing). Includes rubber feet, 2 lifting handles, a starter pack of 10-32 clip nuts & matching black screws. 10.5" Rack Height. Overall height 2" over panel height. 17" deep. Overall width is 21". Recommended maximum weight 600 pounds. Rugged powder paint finish. Hammond Mfg. 38 lbs sh. Drop shipped from NY. New,
$195.77 each
   
 
click to view full size image R390A-Cap   -   Sprague or equivalent 183-0703-00 45 MFD X 45 MFD 400 VDC Capacitor, good replacement for R-390A Audio Deck. D35397 6334 (O1U,M2K) Used
$14.95 each
   
 
click to view full size image MM-R-390A   -   Maintenance Manual for R-390A, repro,
$29.00 each
   
 
OM-R-390A   -   R-390A Operator's Manual repro,
$14.00 each
   
 
82-5589-RFX   -   Twin-Ax Plug, Amphenol, Fits balanced input on R-390A. (E1K) New,
$11.50 each

3 / $30.00
   
 
click to view full size image UG-970-ZZ2   -   Hard to find R-390A balanced input adapter. Goes from Twin-ax male to a UHF female. (S) Unused,
$46.00 each
   
 
click to view full size image UG-971   -   Hard to find R-390A balanced input adapter. Goes from Twin-ax male to a type C female. Unused,
$39.00 each
   
 
click to view full size image UG-573   -   Type C Plug Unbalanced Silver Plated Coax Connector for R390 and R-390A, (M1X,A9Q) Unused Cut-off,
$7.50 each
   
 
R390A-CO   -   Crystal oven from R390A Receiver for the 200KC and 17 MC Crystals. (Crystals not included.
$25.00 each
   
 
390A-200kHz-CR   -   200 kHz Crystal from R390A Receiver.
$20.00 each


   
 
click to view full size image 390A-MBNC   -   Mini-BNC male p/o R-390A receiver, used,
$4.00 each
   
 
click to view full size image 390A-MBNC-RA   -   Mini-BNC male Right Angle, p/o R-390A receiver, used,
$4.00 each
   
 
click to view full size image 390A-MBNC-CH   -   Mini-BNC female chassis-type p/o R-390A receiver, used
$4.00 each
   
 
click to view full size image 390A-MBNC-CH-RA   -   Mini-BNC female chassis-type Right Angle. Similar to part out of R-390A receiver, used
$4.00 each
   
 
click to view full size image 390A-MBNC-LG   -   Mini-BNC male for larger 3/16th inch coax, like part out of R-390A receiver, used,
$4.00 each
   
 
click to view full size image 390A-MBNC-RA-LG   -   Mini-BNC male Right Angle, for larger 3/16th inch coax, like part out of R-390A receiver, used,
$4.00 each


   
 
click to view full size image NT-390A-Amelco   -   R-390A Name Tag (ID Plate)for Amelco,
$29.95 each
   
 
click to view full size image NT-390A-Columbia   -   R-390A Name Tag for Columbia Electronics,
$29.95 each
   
 
click to view full size image NT-390A-Capehart   -   R-390A Name Tag (ID Plate)for Capehart,
$29.95 each
   
 
click to view full size image NT-390A-Dittmore   -   R-390A Name Tag (ID Plate)for Dittmore-Freimuth,
$29.95 each
   
 
click to view full size image NT-390-Motorola   -   R-390 (Not A) Name Tag (ID Plate)for Motorola,
$29.95 each
   
 
click to view full size image NT-390A-StewartWarner   -   R-390A Name Tag for (ID Plate)Stewart Warner,
$29.95 each
   
 
click to view full size image TML390   -   Reproduction Name Tags (ID Plate)for R-390A radios. Motorola Large Print, 3"Wx7/8"H, New,
$29.99 each
   
 
click to view full size image TMS390   -   Reproduction Name Tags (ID Plate)for R-390A radios. Motorola Small Print, 3"Wx7/8"H, New,
$29.99 each
   
 
click to view full size image NT-390A-Teledyne   -   R-390A Name Tag (ID Plate)for Teledyne,
$29.95 each
   
 
click to view full size image T-IMP390   -   Reproduction Name Tags for R-390A radios. IMPERIAL, 2.5"Wx1"H,
$29.99 each
   
 
390-RF   -   R-390A RF Deck Cover for R-390A receiver, Utah plate. Has layout diagram of coils. Used, may have scratches/dents/other marks.
$35.00 each
   
 
click to view full size image 390A-BFO   -   455KHz Beat Frequency Oscillator for famous HF Receiver R-390A. Various manufacturers. UNUSED CONDITION! (N2Y) 3.3x1.5, 2 lbs sh.
$37.50 each
   
 
VFO-R390A   -   VARIABLE FREQUENCY OSCILLATOR from R-390A HF receiver with 5749 tube; used dented less connectors (D2W) "AS-IS", no choice of manufacturer, no Cosmos units available. 4 lbs.
$32.00 each
   
 
390A-ACP   -   AC Line Terminal Protective Cover for R-390A receiver,
$9.95 each
   
 
click to view full size image 390A-PS   -   Transformer - R-390A Power Supply for the R-390-A receiver without tubes, Primary: 2 x 115VAC 48-62 Hz. Sec: 570VCT 200ma, 25VCT 1.2 Amps, 6V 8 Amps. On chassis w/ sockets for two 26Z5 tubes; 20 lbs sh. Used,
$45.00 each
   
 
390A-CO   -   Crystal Oscillator for R-390A receiver(less crystals)
$30.00 each
   
 
390A-CO-WC   -   CRYSTAL OSCILLATOR (with crystals) for R-390A,
$99.00 each
   
 
390A-CO-CVRR   -   R-390A crystal oscillator round cover,
$10.00 each
   
 
390A-CO-CVRS   -   R-390A crystal oscillator square cover,
$10.00 each
   
 
3TF7   -   RT-510 Ballast Resistor Unused Tube by Amperite or equal for Collins receiver R-390A, R-390, R-391, R-389 unused
$60.00 each
   
 
26Z5-UN   -   Unused Tube for R-390A,
$25.00 each
   
 
390A-DC   -   Counter Dial for R-390A, R-390, R-392 receiver, specify which receiver,
$30.00 each
   
 
390A-BZL-CVR   -   R-390/R-390A counter bezel cover w/lamps
$15.00 each
   
 
390A-G-39   -   Gears #39 with clamp,
$14.00 each
   
 
390A-G-21   -   Gears #21 with clamp,
$14.00 each
   
 
390A-GC   -   Gear Clamp 1/4" for 1/4 inch shaft used on R-390A, R-390, R-392 receivers as well as other Collins Radio products,
$4.00 each
   
 
390A-HAND-L   -   Handles per pair less hardware for R-390A and R-390 receiver
$12.00 each
   
 
390A-HAND   -   Handles per pair with hardware for R-390A, R-390 receiver,
$21.00 each
   
 
R390A-SM   -   Small R-390A Knob,
$7.00 each
   
 
R390A-MED   -   Medium R-390A Knob for R-390A and R-390 receiver,
$7.00 each
   
 
390A-SL-IF   -   Slug, IF Variable for R-390A receiver
$7.00 each
   
 
6FF0.1   -   0.1 amp (good replacement for 1/8 amp), R-390A Fuse. New,
5 / $2.50

10 / $3.95
   
 
6FF0.25   -   0.25 amp (good replacement for 1/8 amp), R-390A Fuse. New,
5 / $2.50

10 / $3.95
   
 
6FF3   -   3 amps (good replacement for 3 amps), R-390A Fuse. New,
10 / $1.95
   
 
R-390A-DL   -   #328 Dial Lamps.
2 / $5.00
   
 
390A-SL-RF   -   Slug, RF Variable for R-390A receiver
$7.00 each
   
 
click to view full size image R390A-IF-FILTER-2KHZ   -   Collins mechanical filter for the IF deck of the R-390A receiver, 2 kHz bandwidth. May be branded with other manufacturer name (no choice). Used tested.
$85.00 each
   
 
click to view full size image R390A-IF-FILTER-4KHZ   -   Collins mechanical filter for the IF deck of the R-390A receiver, 4 kHz bandwidth. May be branded with other manufacturer name (no choice). Used tested.
$85.00 each
   
 
click to view full size image R390A-IF-FILTER-8KHZ   -   Collins mechanical filter for the IF deck of the R-390A receiver, 8 kHz bandwidth. May be branded with other manufacturer name (no choice). Used tested.
$65.00 each
   
 
click to view full size image R390A-IF-FILTER-16KHZ   -   Collins mechanical filter for the IF deck of the R-390A receiver, 16 kHz bandwidth. May be branded with other manufacturer name (no choice). Used tested.
$50.00 each
IF Transformers for R-390A

RF Transformers for R-390A

R-390A Crystals - Click Here

R-390 NOT A Crystals - Click Here



   
 
click to view full size image R-761   -   ARC-58 RECEIVER, companion receiver and exciter to T-730. Requires 115 VAC 400 Hz input. 7.8x10.3x23.5 55 lbs sh. (K1D) Used,
$225.00 each
   
 
SCH-R-761   -   SCHEMATIC with set purchase.
$14.00 each
   
 
C-3141   -   C-3141/ARC-58/TRC-75 RADIO CONTROL BOX for frequency selection and control, (E2X) used,7 Lbs Shipping
$30.00 each
MODULES from AN/ARC-58 or TRC-75 radio sets. Each 4.8x4.5 x1.5, 2 lbs sh. USED-not tested:



   
 
AM-1523   -   AM AMPLIFIER DETECTOR, 4x 5899 tubes. Part of R-761, TRC-75 or ARC-58. used,
$30.00 each
   
 
AM-1525   -    or equal ELECTRONIC CONTROL AMPLIFIER p/o T605/T-730 xmitter,
$23.00 each
   
 
AM-1526   -   USB detector and amplifier. Has 300khz 2.6 khz BW bandpass mechanical filter. Part of TRC-75 or ARC-58. used,
$29.00 each
   
 
AM-1528   -   AMPLIFIER-MIXER for R-761 with ten tubes and slug rack,
$52.00 each
   
 
SCH-AM-1528   -   Schematic for AM-1528,
$5.00 each
   
 
AM-1529   -   AMPLIFIER OSCILLATOR with Collins mechanical filter P455 Z1, 526-9308-00 or equal
$40.00 each
   
 
SCH-CV-465A   -   Schematic for CV-465A,
$12.00 each
   
 
MD-286   -   BALANCED MODULATOR with mechanical filters F300 Z4 and F300 Z5, etc. Part of TRC-75 or ARC-58. used,
$40.00 each
   
 
SG-179   -   REFERENCE GENERATOR, (T1Y)
$40.00 each


   
 
click to view full size image NM26T   -   Singer Receiver / Electromagnetic Noise Meter. All solid state, hand portable meter which is precise enough for the laboratory and rugged enough for the field. Covers from 150KHz to 32MHz in eight bands. Intermediate frequency of 455KHz. RF input impedance of 50 ohm (coaxial). 8.8x15.5x8.9, 25 lbs sh. (T1E) Used reparable,
$485.00 each


   
 
click to view full size image NM-17   -   * Singer model NM-17/27 is a programmable, precision electromagnetic interference/field intensity meter for the measurement of conducted or radiated RF interference, within the frequency range of 10KHz to 32 MHz. May be used as a VLF unit. The instrument may be used to analyze narrowband or broadband signals within its frequency range. Field intensity or direct peak detector functions may be used for measurements in addition to quasi-peak, slideback peak and BFO detection modes. AM, FM and PM signals may be detected and are available at the video output receptacle for oscilloscope display. Requires 115/230V at 50 to 400Hz. 18.5x16.7x8.7, 55 lbs sh. (T1B) Used reparable with manual repro,
$595.00 each


   
 
GSB-900RU   -   SUNAIR RECEIVER NO CONTROL, Very good physical condition. No control, unable to test. used reparable,
$375.00 each


   
 
BR-3008-YY   -   BR Communications 3008 remote start interface, Used Reparable,
$195.00 each


   
 
BR-4028-YY   -   BR Communications 4028 Receiver, Used Reparable,
$295.00 each


   
 
TCS-9   -   TCS-9 Receiver. Used not checked,
$175.00 each
<< Prev      Currently viewing page 1 of 1      Next >>
Page: 1



Home Products Email us for Catalog or Inquiries Order Form Terms & Conditions Shipping Rates


Any problems with the website? Email webmaster@fairradio.com